General
45 results found
-
Connection points
Connection points within a circuit to avoiid too much wires.ß
16 votesAvailable right now with v1.12 as Internal Ports
-
optocouplers optoisolators
Are these available to add into the circuits. If not any chance they will be available any time soon???
14 votesThis will be available in iCircuit 1.13! Thank you for your patience
-
Display the Pin numbers of IC
It would be very usefull to display the actual pin numbers of IC aside the pin function
E.g for the 555 timer, instead of just CTL it is better to show 5 (CTL).
It helps a lot when taking reference circuits that most of time only show pin numbers9 votesPIN numbers are available in v1.11 and onward
-
Please add the cmos cd4017 decade counter/divider
It is an extremely useful and popular chip for many diy projects.
8 votesYou can find this IC in the ICs section now!
-
Seed this forum with your ideas
UserVoice pro tip #1:
Your customers are full of ideas, but people are more likely to contribute if they're not among the first. Add your own ideas now!3 votes -
Crashing since last update
Every time I call for information, or edit, or add a new circuit the app crashes. What's the issue? Just unstable code?
4 votes -
Ability to colour wires
I sometimes run harnesses with 12 or more wire colours (pink, pink/blue trace, white, red, orange, orange/ green trace etc etc) yes I can label the colour but it also make it very quick to identify pathways via colour.
4 votesWire colors are now in version 1.12
-
4 votes
In the up-coming 1.11, you will be able to override the OS language and use English.
-
remove 1ohm potentiometer issue
the potentiometer has a 1ohm boundary. It is not mathematically correct, and not good when using the potentiometer in low-ohmic circuits. To demonstrate the bug, put a dc source across the pot with a value of 1 or 2 ohms. now vary the pot position.... the voltage at the wiper is not correct. Also observe the R1 and R2 values if setting the pot to 10ohm and the wiper position at 0. You now have an 11ohm potentiometer.
3 votesFortunately this problem has already been solved
-
Ad a 74595 shift register with serial-in/paralel-out
There should be a ic shift register with serial-in/paralel-out.
3 votes -
Have the Arduino “attachInterrupt” enabled.
The Arduino device does not recognise the “attachInterrupt”. Without this then circuits that interact by interrupts in real random time with the Arduino cannot be simulated. It may be a big ask, but without it I am stumped in developing my ignition system.
(There may be a French person asking a similar thing, but my French isn’t good enough to be sure...)
3 votes -
i need 7490 7492 7476 chips!
i need 7490 7492 7476 chips!
2 votesAvailable now in the ICs section since v1.12
-
Redo button
Add elimination options for components currently in use, as well as an redo button
1 voteYou can redo by long pressing the Undo button.
-
1 vote
analogRead is supported in 1.9
-
1 vote
-
ad new compoment 74ls83 adder
I would like to use this one and make a diagram but the software doesnt has it. Can you put it in the next version?
http://pdf.datasheetcatalog.com/datasheet/motorola/SN74LS83D.pdf1 voteAvailable now in the ICs section since v1.12
-
Remove matrix error
Some circuits i creat have multiple earthy points (auto electrician) every time more than on earth is added to a circuit it creates a matrix error.
1 voteIn v1.11 of the app, the element that is causing trouble for the simulator will be highlighted. Hopefully that will help you determine the short in the circuit.
-
3.3V Arduino
I mostly use the AtMega with 3.3V and it would save me a lot of additional design if I could have 3.3V directly out of the Arduino's Pins.
1 voteThis will be in version 1.11.2
-
555 chip missing ground?
The 555 chip appears to be missing the ground pin?
1 voteYou can choose “Show Ground” in the 555’s properties. This will become the default in version 1.11.
-
4043
please add this chip too.
thanks1 voteAvailable now in the ICs section since v1.12
- Don't see your idea?