General
553 results found
-
4 votes
-
Would be great simply to have more draw options
I need it to label my circuts the the tools in circuit are very limited.
I need to resize the text box freely, put some terminals with free numbering. etc.2 votes -
Add microcontrollers such as pic atmega etc.
I would pay 50 bucks more for it :)
21 votes -
add more models
Certain devices, for example transistors, have different models, specified by their model numbers, and each has different parameters.
3 votes -
Add L293D H-Bridge Motor Controller
Please add a digital component for L293D H-Bridge Motor Controller
4 votes -
L293D H-Bridge Motor Controller
Please add digital component for L293D H-Bridge Motor Controller
0 votes -
Since you have a plan to add ic chips to show as chips, can you let us create custom chips?
Have a "custom chip" that allows us to design a circuit to put in the chip, then, show the chip as an IC in our main circuit. If we click on the chip like we are going to change the settings it shows our sub-circuit that is in the chip so we can edit it. Include a back arrow on the sub-circuit for when we want to go back to the main circuit. You can limit which components we can put in the custom chip if it gets too complex to do the simulation. For example, no switches inside the…
2 votes -
Add optoisolators
Optoisolators are missing components.
7 votes -
Basic vacuum tubes
Just a the basis models
11 votes -
1 vote
-
More interfaces and converter.
I wish i could convert and show binary as hex and dezimal values.
Or look what data was send on a serial or parallel interface.Could you make some more complex converters and bus systems and IC's ?
1 vote -
Using LM78xx input current must be equal to output current
When using voltage regulators LM78xx (great idea), I observe than intput current is set to cero, while output current works according output circuit.
Could be possible set input current equal to output current? This is a good aproximation (input might be output current plus a inner consumption).8 votes -
Potentiometer upgrades
instead of a menu item, it would be lovely if you could click and drag the value of a potentiometer. Then the actual value of the pot would be displayed in the menu.
linking two pots together... so when one moves the other adjusts.
4 votes -
Programmable PIC
It would be amazing if you could add PIC and make us able to program them for simulation and testing just like the in multisim, for example "PIC16F84A".
6 votes -
Fix the switches
With the scope running, tapping a switch to change it's state causes the switch parameters to be displayed on the scope. This should not happen.
Also: add a time-dependent switch
17 votes -
If you push R for resistor... pushing R a second time would rotate the resistor
Shortcut keys are helpful, but rotating components in a PITA
Pushing the shortcut key a second time could rotate it
11 votes -
Make elements library more customizable
Users should be able to add custom elements to any existing category of elements and create new categories. Also, key shortcuts should be customizable. For example, if a user uses digital elements more than analog elements, they might change 'A' to map to an AND gate rather than an AC source, or 'C' to a square-wave source (like a clock).
6 votes -
Allow specifying which side of the sub-circuit a port is on
It would be extremely convenient if ports had an option of specifying which side of the box the wire is on (ie to separate inputs from outputs). For example, I am making a 3-bit counter with two inputs and three outputs. However, because iCircuit tries to balance the sides, it puts both inputs and one of the outputs on the left side and two of the outputs on the right side. This is extremely frustrating. If possible, I'd like to even be able to put ports on the top/bottom of the sub-circuit box.
8 votes -
realtime ajusting component.
I dont know if Icircuit has it ?, but
in Every circuit, you can for eks, change
resistor in realtime,observing LED gets
brighter.
Allso some improving with the graphics layout, component!
ohms low / circle etc..3 votes -
Schmitt Trigger opt
Have Schmitt trigger option for logic gates, like a 4093 (NAND)
3 votes
- Don't see your idea?