General
564 results found
-
please add IC HT12E for my RC
IC HT12E beacause i learn to make RC
4 votes -
enable opamp self-oscillation
I am attempting to model a simple self-oscillating opamp circuit of the sort often used as square/triangle oscillators in synthesizers, but can’t seem to get the simulator to model this the way that it works on my breadboard.
4 votes -
Allow scaling the timebase
I'm doing a circuit that's meant to process audio-frequency inputs. I'd like to see just what the different components do as the input signal changes. Problem: the display is all real-time, so unless I set the input frequency to, say, 1Hz, there's no way I'll see the results. And then, my RC circuits are all wrong due to the incorrect frequencies.
Suggestion: allow scaling the timebase by 10x, 100x, 1000x, etc. This means that time in the circuit would pass at 1/10, 1/100, or 1/1000 real time (e.g. at 1000x it would take a full second for a millisecond of…
6 votes -
Enable selection of both "Must Operate" and "Must Release" voltages for Configurable Relay component
The Configurable Relay component currently has a fixed operating voltage around 75% of the specified Coil Voltage. The same voltage applies to both Operate and Release transitions.
However, most small relays have different "Must Operate" and "Must Release" voltages. Typically around 75% and 15% respectively of the rated Coil Voltage
Some circuits can't be properly simulated in iCircuit because there's no way to select the "Must Operate" and "Must Release" voltages.
It would be desirable to enable an option to do so.
1 vote -
Flip should NOT be the same as rotate
There's a button to "flip" a component, but in some cases it just rotates the component, for example relays, and in other cases it actually gets a symmetric flip in one single direction, so you can't actually perform a true rotation, for example transistors. In some cases this makes imposible to get the desired orientation or rotation.
1 vote -
Asking for adapting to the Magic Keyboard and some problem below.
Hope you can adapt to the Magic Keyboard.
And when I coding arduino UI would be awful.
When you type a long code you can’t see the code behind.
Hope you can fix the problem.5 votes -
Remove close loop inhibit
In automotive, sometimes I have multiple earths or supplies on close loops. The ability to turn off the error message function would be very helpful in some cases as many of my circuits are printed in pdf and supplied to a CAD developer
3 votes -
Can't create subcircuit on android
I can't create sub circuit in android I need help
6 votes -
add debugger to uno editor
could really make life easier
1 vote -
Add Logic outputs
Simple H or L output gauges
2 votes -
Add working/supply voltage option to all logic elements
Currently 5V logic is rarely used in real life. It would be nice to define this voltage in all gates, flip-flops etc. Voltage slider or at least standard values 5V, 3.3V, 2.5V, 1.8V, 1.2V.
2 votes -
Limiting values of resistors/capacitors/inductors to series E12,E24,E48 etc
It would be nice to have buttons with names of standard series E12,E24, etc. next to value slider. Then slider should only use standard values. It is better to use only values that you can then use in real circuits. We rarely use other capacitor values than those from E3 or E6 series. Resistors usually only from E24 etc. The same limitations may be added to zener voltages. There are standard values like 4.7V, 5.1V, 5.6V etc. Why to use 4.8V zener in simulation when you can’t buy one.
3 votes -
The ZH-HANS Translations is on old version and does not supported fully in new versions, please update the Base.lproj files on the github
The ZH-HANS Translations is on old version and does not supported fully in new versions, please update the Base.lproj files on the github.
I want to help to translate it but the Base.lproj is for the old version and do not include the newer version's elements.Plz update the Base.lproj to the newer version. Thanks.3 votes -
1 vote
-
Add ability to select default theme
I the app is a joy to use, but don’t like having to select black every time
1 vote -
a complaint
icircuits has a few flaws,the n chanel and the p chanel jfet transistor s symbols laks a gate a drain and a source and its not acurate,try this experiment pleas 5vdc as a source of power,conect drain lead of the n chanel jfet to + of the 5v power source and the source lead to to the - of the 5v power supply and short the gate to the - of the power source and click on of the simulated wire and see the results its lik theirs no short cuit at all between the gat and the source,i tryed…
1 vote -
7400 ICs are always using 5V levels despite using non-5V VCC
7400 logic levels should depend on supplied VCC as these ICs can run normally with 2-6V and logic levels (VIH, VIL, VOH, VOL) depend on the VCC which is described in data-sheets. Hence 5V should be only used as a convenience when VCC is not connected at all.
2 votes -
Simulator start/restart and pause keyboard shortcuts
Please add keyboard (and menu) shortcuts to start/restart and pause simulation. Ideally Cmd+R to start/restart, Space to pause/unpause - replacing Edit mode which could be switched by Escape instead.
1 vote -
Clicking on oscilloscope should reveal its properties
Currently to reach oscilloscope properties I need to click Oscilloscope switch button which is very confusing and cumbersome. It would be much easier if I clicking on oscilloscope would switch to its properties. And consistently clicking on empty circuit region should always show circuit properties. Right now this happens only when some component is selected, and then it gets deselected.
1 vote -
Oscilloscope plot lines are too thick and get even thicker when enlarging the view
On macOS oscilloscope lines are far too thick and what's worse they get thicker when I enlarge the view to see more details. Please make thickness constant and ideally adjustable and persisted via View > Line Thickness.
3 votes
- Don't see your idea?